Power Commander
They are only used on 4T engines with electronic fuel-injection.
Allows to adjust the fuel curve acting on injection, on baffle position and on the pressure in the intake manifold. A separate unit for advance control can be added. Anyway, we suggest to vary the advance only when using gasoline with octane number higher or equal to 98 (like Shell V-Power or Agip Blu Super). In some cases, by the advance control unit, it is possible to vary the number of engine rev. at which the limiter operates. 
Carburetion can be varied for each cylinder separately. It is also possible to vary the advance for each cylinder separately by adding the advance control unit.
The use of Power Commander considerably increases performances and allows to bring engine carburetion into line with any conversion, replacement of the exhaust system, air filter, etc. They can be easily connected directly to the bike original management system. You just have to remove the connector from the original management system and connect it to the Power Commander, then join the Power Commander connector to the original management system.
For programming, a software and a PC link cable are supplied in the kit (an USB port is used).
Different stages of basic adjustment are available to fit all your carburetion requirements (when ordering, please mention exhaust system and air filter mounted on your bike and any modification on your engine). By using the PC interface included in the kit, you can however change the parameters at your choice.
Dynojet regularly update its mapping and you will find the latest ones at www.powercommander.com web site.
It's also possible to make approximate adjustments of ignition only, directly on the management system, by the three buttons thereon. The LED display will facilitate tuning. NOTE
In order to get your Power Commander with the correct basic programming, please specify in the "Notes" section:
- exact model of your bike
- production year of your bike
- exhaust system you are currently using (brand, only silencer or complete, racing or approved)
- air filter you are currently using
- any other changes made in the engine or in the air-box. | QuickShifter electronic gear
Allows to change gears increasing without turning off the gas and without pulling the clutch lever, just like in speed races.
In fact, turning off the gas, even a bit, slow down the times on the lap and can make the difference between a victory or a defeat. Once the device is installed on the bike, the pilot can increase gear just operating on the gear shift. The Quick Shifter works on the engine ignition directly. Intervention time can be adjusted by the software supplied.
The user can also adjust the engine minimum rate by which the system will work. This prevents from making the system work at a lower rev rate than that indicated, for instance in case of street driving at low speed. The Quick Shifter must be used with and connected to the PCIIIusb Power Commanders exclusively. No changes to the electric system and stock wiring of the bike are needed. The electronic gear is made of a sensor to be installed on the gear pedal and connected to the PCIIIusb. Different standard solutions are available, or specific for some particular bike models, for quick mounting with no need of changing or making anything.
| PCIIIusb firmware updating connector
For updating the PCIIIusb firmware through direct connection to your computer with usb output. Weight Kg 0.04 Delivery in 1-5 days from your order. | |  #EPROG |
| 9 V battery adapter
To supply PCIIIusb (to be used only if programming is made without connecting to the bike). Weight Kg 0.01 Delivery in 5-20 days from your order. | |  #66116002 | | | Multifunction hub
Kit includes multifunction hub with Cd Rom for firmware updating, map selector switch with wiring and switch mount on the handlebar. When connected to the PCIIIusb, all new Power Commander fittings can be used. By the selector included, 2 different mapping can be chosen. It's very useful during competitions and also for touring, choosing between"low consumption" and "performance" mapping.
Hub needs the PCIIIusb firmware updating. To this purpose, it is essential to have the #EPROG connector which is included in the additional advance control module. You can also find this item on this page, to be purchased separately. Weight Kg 0.13 Delivery in 5-20 days from your order. | | 
#HUB002
|
| LCD display
Can be both temporarily and regularly connected to the Power Commander on your bike, for it is entirely water-proof. Characteristics:
- shows PCIIIusb data in real time and stores them
- stores several mappings that can be afterwards selected at choice
- allows using more additional storage by SD memory card
- can be programmed and up-dated by USB input
- TFT LCD display touch screen, 240 x 320 pixel, 16 bit colours. Weight Kg 0.23 Delivery in 1-5 days from your order. | | 
#LCD100
|
| Quick shifter electronic gear shift unit
Allows the function of electronic shifter acting on ignition directly and using already existing Dynojet sensors missing the Power Commander. Provided with coil connectors ready to be mounted. It is to be used in combination with the range of sensors operating Dynojet electronic gearshift that we offer as accessories of the Power Commander (see pages of specific applications).
Weight Kg 0.33 Delivery in 5-20 days from your order. | |  #E4-112 | |
Tidak ada komentar:
Posting Komentar